Our First Spring Launch — Part 2

You may want to read Part 1 of our spring launch adventure to get up to speed if you haven’t been following along. The launch has gone well despite a few hiccups. One of those hiccups has been water coming into the sailboat. When our daughter nicknamed Azura “the leaky beak” after a boat in Jake and the Neverland Pirates we thought it cute. That was, until Azura actually lived up to the moniker.

valve core removed

Bryan headed out to the marina very early on Sunday. I stayed home to prepare for my son’s 16th birthday party and a house full of teenagers. Bryan would join the festivities later in the day. Later that morning he would meet with Yunior, the mechanic. Bryan organized his tools and did a few other jobs on the sailboat until the mechanic was available. Then they set to work on Azura’s issues.

Water was dripping into the sailboat because of corrosion on the core of the blackwater discharge valve. When Azura was first put into the water on Saturday the leak was more significant. Dripping had slowed to once every five seconds by the time they were ready to deal with it. There was a problem because the nut was difficult to access. The mechanic mentioned on Saturday that he would create a tool to make it easier to loosen the nut but on Sunday he chose a different plan of attack. Yunior heated the valve with a blowtorch so he could remove it easily.  He cleaned the valve core and put it back in position. Issue resolved.

The stuffing box leak was the next problem. This is a cylinder that houses a shaft that travels from the inboard motor to the propeller. Its purpose is to keep sea water from coming into the hull. The mechanic put some heat to the locking rings with a blowtorch because they refused to budge. It is not an easy spot to get into so Yunior had to be a bit of a contortionist. He got the rings moving, tightened everything up, and stopped the leak.

Bryan and Yunior started Azura’s engine for the first time since she had been taken out of the water in 2015. When we were inspecting the sailboat we didn’t check the engine. Instead, we spoke to the mechanic who had maintained it. We also went over the maintenance and service log that was on Azura. I suppose in hindsight, it was a bit of a risk. We didn’t expect any issues because it appeared to have been well maintained and properly winterized. Thankfully, the engine started up beautifully. The water pump gasket was leaking while the engine was running but would be an easy fix.

new home on dock D

Moving Azura over to her temporary slip on D dock was the next order of business. Yunior asked Bryan how long he has been sailing and the reply was, “once I move the sailboat over to that dock, ten minutes.” I don’t think the mechanic knew if Bryan was pulling his leg or not, at least not at first. The sailboat was moved and Yunior helped Bryan secure the mooring lines to the dock cleats. Azura was home!

It was then that I heard my smartphone. I was expecting the news that Azura’s launch was complete but that isn’t what I saw. Bryan had sent a picture of the toilet paper holder in the head. He put a roll on… the wrong way!! This is a constant debate in our house—I’ve always felt that toilet paper should go over and he felt strongly for it being under. His photo came with the comment “and it’s going to be like that for an entire week!” Brat!

Our First Spring Launch – Part 1

Are you ready to read about our first launch with Azura? You might want to prepare a hot beverage and get comfy because I’m not sure that brevity is going to be my strong point today.

When we bought Azura, the sailboat was on the hard. For you non-sailors among our readers, that means she was sitting atop a cradle in the compound. The survey from a few years back was good but we were still taking a bit of a  risk in buying a sailboat that we hadn’t ever seen in the water. That said, seeing Azura out of the water gave us a great opportunity to thoroughly inspect the hull. Saturday’s launch was a little daunting and part of that could have been that we’d never launched a sailboat before.

ready to launch

The night before, Bryan and the marina staff positioned Azura at the travel lift so that she could go straight into the water on Saturday morning. Bryan, our daughter Kaia, and I headed out early that morning while our teenage son, Tobias, decided to stay home to work on a school project sleep in.

Paul, one of the marina employees, already had Azura in the sling above the water when we arrived at 8:30 am. The day was proving to be gorgeously warm—quite a drastic change in weather from the previous two days of rain and snow. Bryan and I figured it would take an hour or so to launch, then we’d spend the rest of the day setting things up in the cabin, exploring Port Dalhousie, and then head home in the late afternoon.

The first order of business was for Bryan to hop on board and double check that everything was closed properly before the sailboat would be lowered into the water. He did that and we were good to go. As Azura was lowered I held my breath. Everything seemed to be going without a hitch and then it happened… a few moments later I heard Bryan shout out to Paul that Azura was taking on water. *&#$!

Further inspection indicated that we had leaks in two places. The one spot, which is common, is called the stuffing box.  This is where the shaft for the propeller leaves the sailboat. It would be fairly easy to access and wasn’t something he was overly concerned about. The other spot was the waste discharge valve. It is illegal to have this functioning on the Great Lakes and pretty much any inland waterway. It had been fiberglassed over as well as sealed off  properly but it seemed the nut wasn’t tight enough and water was coming into the bilge. Bryan tried to tighten the valve but it was impossible to get at. He explained to me that we may have to pull Azura back out and access it from the outside.

What is it that they say about the best laid plans?

Paul told us that there might be another way and he called in their marine mechanic to look at our issues. Yunior, a very helpful and friendly guy who originally hails from Cuba,  said that the leaks were small enough that we wouldn’t sink and he didn’t think we needed to pull her from the water just yet. He suggested that Paul and his helper help Bryan line Azura to the service dock and he would come back the next day. Yunior was going to make a tool that would allow him to access the nut from inside the sailboat to tighten it. He would also take care of the stuffing box then.

stepping the main mast

While Bryan was taking care of all of this, Little Miss Kaia and I settled the bill for our summer stay at the marina. We explored the marina grounds, took quite a few photos, and then headed back to the office. We had a lovely chat with Laura and Nena who own the marina. Kaia politely asked Laura for a garbage bag. She wanted to clean up some garbage she saw around the rocks and in the gardens. I put gloves on her and we set to work. It was so sweet of her to offer to help and a great way to keep her out of trouble. Kaia isn’t quite seven years old and all the waiting had to be pretty boring for her.

Now back to our sailboat. Paul and Bryan decided that they would step the masts before moving Azura. Stepping the masts is fancy sailor talk for putting the masts up. Our main mast was very heavy and took several men to lift it onto the transport truck at the Lake Simcoe end during the move. Thankfully Paul and the guys had put it on  a cart the night before and it could simply be wheeled up to the crane. Within an hour, they had both the main and mizzen masts up and Bryan was tightening the shrouds. Azura was then lined to the service dock and we went for a late lunch.

Upon returning we loaded Azura with all the gear we brought from home. Kaia and I spent the remainder of the afternoon organizing Bryan’s tools as well as a plethora of spare parts that we found in the hanging locker. We set up the cushions in the vberth and puttered around. Kaia read her books, played on her tablet, snuggled under a blanket on one of the berths, snapped some photographs, and even helped do some sweeping.

Bryan had been installing the booms when he heard a ruckus across the water. We looked over to see a couple struggling with putting their mast on. A third boater came over to help and the mast was precariously position. In fact, it was close to landing in the drink. He immediately dropped what he was doing and ran along the docks to go help. It was a good thing he did and a half hour later they had it in place. It was educational for us because we had considered stepping the masts ourselves. After seeing that I think we will stick to the crane.

view towards the lake

Later in the day, Bryan decided to check the bilge pump. He disconnected it from the hose and put it in a bucket of water. It didn’t go off like it should have. He checked the wiring to ensure it was getting power. It was. Finally, I suggested that he just go get a new one. I figured the bilge pump was necessary especially with the leaks still not being repaired at that point. Perhaps I might have been overly cautious but that is my nature. I found a shop nearby that had a new pump on sale for a reasonable price. It was 5:30 pm by this time so Bryan hurried off to pick it up as well as something for us to eat.

After a quick bite, Bryan set to work installing the new bilge pump… and it wouldn’t work either. He checked all the wiring again and discovered that the ground wire had come off at some point in time. He put the ground back in place, successfully tested the pump, and reconnected the hose. We decided that we would keep the old pump, which wasn’t broken after all, as a backup.

We called it a day, watched our first sunset from the cockpit, then headed home. The plan was for Bryan to return on Sunday to meet with the mechanic and try to rectify the leaky business while I prepared for a housefull of teens. In my next post I will share the second part of our launch story.

More photos (click to enlarge)…

docks to be set up
at the service dock
the setting sun






A Few Little Projects

Is it Spring yet?

a hatch needs rebuilding
a hatch needs rebuilding

I’m confident that the next six months are going to feel much longer than they are in reality. It seems like a long wait for Azura to be transported to our marina spot at Port Dalhousie. Until then, there are many little projects that we can do throughout the long winter.

Carpentry will be Bryan’s focus. He needs to rebuild the floating wood section that serves as the cockpit floor—it’s showing some signs of rot. Then another important bit of work will be to replace or restore one or more of the hatches. The dorade boxes are a little worse for the wear too. There is some trim work on the deck that needs replacing although I think that will have to wait until she is in the water. The trim in question has been painted white but originally was stained. We’d like to go back to unpainted wood because it looks very striking. I’m not sure what else Bryan has in mind except there has been a brief mention of making a folding cockpit table.

My projects surround the galley and berths. The biggest task for me is to find a suitable alcohol stove so I’ll be visiting Ontario Boat Wreckers. Hopefully I can find a two-burner model in good condition.  I’ll need to start gathering the basics for a sailboat kitchen such as pots, pans, a kettle, and utensils. We will also need cutlery and dishes. I think that something unbreakable or break-resistant is in order.

dorade boxes need repair
dorade boxes need repair

I’ll be breaking out the sewing machine to make new curtains, recover or replace the cushions for the two berths in the common area, and make some custom sheets for the v-berth. There will be some room for creativity as I will be creating some throw pillows to add a splash of colour.  I’ve been thinking of sewing up a few coordinating bolsters to house the sheets and blankets when we aren’t sleeping.

All in all there isn’t a ton of work to do before we start sailing. There will be a little bit of work on a few spots where there is some minor crazing but considering the age of this sailboat, it is in great shape. There a few other creative projects swimming around in my head, but I’m keeping those under my hat so that I might surprise Bryan for Christmas and his birthday.

By the way, I’ve been collecting information about sailing and items that inspire me on Pinterest. If you are curious please click the Pinterest icon at the top of the page to check it out.